Detune Box
Detune Box

Over the years, thousands of wireless towers around the United States have been detuned to nearby AM stations. They have been detuned because the Federal Communications Commission rules require wireless carriers and other tower users to protect AM broadcast station antenna patterns. See our AM Protection FAQs.

The same FCC regulations require “the continued maintenance” of these AM protection systems. It is an FCC violation not to do so.

Regrettably, many operators of detuned towers have missed this part of the rules, and many AM detuning systems are in a sad state of repair. This not only violates the FCC rules, but jeopardizes the AM station functioning, and can even lead to civil liability!

Wireless engineers are well versed in cellular systems; however AM engineering concepts are often not included in their education or experience. Thus, it’s easy to overlook detuning maintenance. AM detuning systems are entirely passive, have no failure bells and whistles, and their failure in no way affects the wireless carrier operation.  The systems are just some more wires and cables among many on a tower.

When the AM detuning system is installed, it is a “set and forget” procedure. Left undisturbed, that initial setting is likely good for many years. Unfortunately, that happy state is rarely achieved on a communications tower.

An AM detuning system consists of a wire cage about a tower, often to the top, and a tuning box with components to resonate the system to the AM frequency. While deceptively simple, the devil is in the details, and almost any disturbance to the mechanical or electrical configuration of the system can cancel out the AM detuning effects.

A few years ago, an LBA engineer did a study of over 100 cell sites and found that only 25% were in FCC compliance! Amazingly, some sites were improperly installed, or used the wrong components, and could never have been detuned.

How do AM detuning systems fail? LBA has been responsible for deploying and rebuilding hundreds of these systems. Here are some of the major failure modes our engineers see:

  • Lightning strikes – Often invisible on the exterior, lightning fries components and shatters insulators inside the detuning cabinet. It is also known to destroy system standoff insulators on the tower. See LBA tower and antenna lightning protection systems.
  • Wind – May disrupt detuning cables, or displace other tower mounted antennas and mounts to touch detuning wires.
  • Poor construction – Too many systems are of the “cheapo” variety, often using light construction, unsuited to the robust utility grade requirements of tower survival. Like the proverbial “One Horse Shay”, these systems often just simply fall apart after a few years.
  • Tower climbers – Not knowing their function, it is just too tempting to get those detuning wires out of the way by wrapping them around climbing pegs, or clamping them to the tower with a new antenna platform.
  • Environmental – Often vendors have ignored incompatible metals, leading to corrosion on connections. Some have used detuning boxes that are not weather tight, leading to water and insect damage.
  • Tweakers – Only qualified engineers should be permitted to adjust the detuning system. When unqualified persons try to adjust the system, they most often leave it non-functional, but there is no physical evidence in their wake! Only skilled tests can then find the problem and set things right.

There is no required inspection period for AM detuning systems in the FCC rules. However, it is generally thought that a two year inspection and recalibration interval is appropriate, and LBA concurs with that. Of course, a special inspection would be appropriate if irregularities are noted in between times, major tower modification or antenna construction is undertaken, heavy ice or wind occurs, or the site is vandalized.

We also recommend several good practices to minimize the requirement for detuning system repair or replacement:

  • Site warnings – Prominently post the site as detuned, and require that any issues be discussed with site authority or the detuning system vendor.
  • Contractor briefs – Site contractors should be briefed on avoidance of detuning damage and the requirement to engage a qualified detuning vendor to assist them if modifications are needed.
  • Durable construction – Only systems using “utility grade” construction from a proven vendor should be installed. Inferior systems should be replaced at first opportunity.
  • Site log – Any inspection, access to detuning controls or system changes should be part of a permanent site log with date, activity performed, inspection results, and approving authority.

Over the years, Lawrence Behr Associates and LBA Technology have been at the forefront of AM protection and AM colocation for the wireless industry. We have a complete service to inspect and rehabilitate your detuning systems. LBA can perform a system wide evaluation of detuning compliance for you, and follow it up with programmatic services to make your wireless system FCC AM compliant and keep it that way. Contact Mike Britner today!

About The Author

Avatar photo

LBA Group, Inc. has 60 years of experience in providing RF asset solutions and risk management for industrial and telecommunications infrastructure assets. The group is comprised of LBA Technology, a leading manufacturer and integrator of radio frequency systems, lightning protection and EMC equipment for broadcast, industrial and government users worldwide; the professional consultancy Lawrence Behr Associates and LBA University, providing on-site and online professional training. The companies are based in Greenville, N.C., USA.

1 Comment

  1. My brother wanted to invest in a business that plans to build up a wireless construction tower. It’s great to learn that the AM detuning system consists of a wire cage and a tuning box with components that produces the systems to the AM frequency. If my brother will push through with the plan, I hope they’ll be able to find an excellent wireless construction service.

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>

This site uses Akismet to reduce spam. Learn how your comment data is processed.